Toluene diisocyanate manufacturer Knowledge Covestro Dispercoll® U62 heat activated waterborne polyurethane dispersion

Covestro Dispercoll® U62 heat activated waterborne polyurethane dispersion

Covestro Dispercoll® U62 heat activated waterborne polyurethane dispersion

Features

Water based polyurethane dispersion.

Dispercoll® U 62 is an aqueous dispersion of anionically modified polyurethane.
It is a raw material for adhesives formulated for use in the footwear, furniture or automotive industries.
Its characteristic polymer properties make Dispercoll® U 62 particularly suitable for heat activated adhesive applications with high tack and good initial heat resistance.

Supply Form Dispersion

Appearance Milky white

Specifications

Features Number unit Test method
Non-volatile content
(1 g/1 h/125 °C)
46 - 50 % DIN EN ISO 3251
Viscosity
at 23 °C,
spindle L 2 / 30 rpm
50 - 1000 mPa·s M092-ISO 2555
pH 6.0 - 9.0 DIN ISO 976

Features /application

Delta® U 62 performs excellent on most synthetic and natural materials heat resistance and water resistance. It is recommended to add 0.5% ~ 2% of carbodiimide type curing agent for one-component system. Compared with traditional two-component system, this system has no limitation on the pot life. The carbodiimide curing agent Desmodur 2802 from Covestro can be used in conjunction with Dispercoll U62 at a ratio of 0.5% to 2%. based on customer requirements, can add 3-5% (weight ratio) of water-emulsifiable cross-linked isocyanate Desmodur® product line for two-component systems, which can improve the heat resistance and water resistance of the adhesive. The isocyanate crosslinker should be added immediately before application and mixing for strengthening. Pay attention to the working time of the mixed adhesive.
In order to expand the technical performance of special application fields or customized products, resin dispersions, emulsifiers, thickeners, etc. can also be added. Before use, especially before spraying, the prepared adhesive product must be filtered to remove polymer particles that may form in the adhesive.
For heat-activated adhesive applications of Rebaky® U 62 a temperature of 50-70 °C is recommended to ensure that the dry bondline is fully activated. The actual temperature required for a specific application will depend on the pressure time, pressure level and the substrate being bonded.

Save

- Store in original Covestro airtight container.
- Recommended storage temperature: 15 - 25 °C, should avoid exceeding 30 °C.

- Keep out of direct sunlight, freezing, heat and foreign substances.
General information: The product is very sensitive to low temperatures below +10°C, which will cause irreversible damage to the product. Avoid higher temperatures above 30 °C. Prolonged storage at high temperature may affect product performance. Containers must be kept airtight and out of direct sunlight, otherwise evaporation of moisture will result in the formation of a non-dispersible polymer film.

Save Time

Covestro declares that the product is stored in full compliance with the Where required and properly handled, the product complies with the specifications or characteristic values ​​stated in the above clause "Specifications or characteristic values" (as applicable) within 6 months from the date of shipment stated on the transport document.
The fact that a product exceeds the aforementioned 6-month period does not mean that it no longer complies with the values ​​set forth in the specifications or characteristic values. However, Covestro recommends that products older than 6 months from the date of shipment be tested before use to confirm whether they still comply with the values ​​set forth in the specifications or characteristic values. Covestro makes no promises and accepts no responsibility or liability for any failure to conform to the specifications or values ​​set forth in the Characteristic Values ​​for products more than 6 months from the date of shipment.

Disposal Follow current security data manual.

Security

This product data sheet applies only to the latest version of the corresponding safety document. Any updates to safety-related information consistent with legal requirements will only be reflected in the Safety Data Sheet, which will be updated and published. Information pertaining to current classification and labelling, application and process methods, and additional safety data can be found on the most current valid safety data sheet.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.allhdi.com/archives/1564

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Back to top
Home
E-mail
Products
Search