Toluene diisocyanate manufacturer Knowledge Flexible waterproof putty

Flexible waterproof putty

Flexible waterproof putty

1. Product characteristics:

1. Good crack resistance, good elasticity, can independently bear the role of resisting base cracks, and can significantly improve the decorative effect after elastic coating application.

2. It has strong adhesion to the base surface and elastic coating, and can effectively solve the peeling phenomenon of elastic coating.

3. Can be used with various coatings.

4. Easy to construct and polish, resistant to water and alkali.

2. Scope of application:

It is suitable for scraping and leveling the cement mortar, concrete, lime mortar, cement fiber and other base layers of building exterior walls before coating. The exterior walls of buildings, when matched with elastic coatings, can resist micro-cracks caused by various reasons, and jointly solve common minor cracks and other non-structural cracks.

3. Performance indicators:

Detection items

Performance requirements P type

Test results

Individual evaluation

Container status

No lumps, uniform

No lumps, uniform

Qualified

Constructability

No difficulty in scraping

No difficulty in scraping

Qualified

Drying time (surface dry),h

≤5

2

Qualified

Initial drying crack resistance (6h)

No cracks

No cracks

Qualified

Polishability

Can be polished by hand

Can be polished by hand

Qualified

Water absorption, g/10min

≤2

1

Qualified

Alkali resistance (48h)

No exception

No exception

Qualified

Water resistance (96h)

No exception

No exception

Qualified

Bond strength, Mpa

Standard state: ≥0.6 Freeze-thaw cycle (5 times): ≥0.4

Standard status: 1.2 Freeze-thaw cycles (5 times): 0.8

Qualified

Dynamic cracking resistance,mm

Base layer cracks≥0.1,<0.3

Base layer crack 0.3mm

Qualified

IV. Construction methods:

1. The base surface must be solid, clean, flat, free of dirt, loose, sandy, and peeling.

2. This product is a single component and can be used directly after opening the cap.

3. Apply a full batch of this product 2-3 times, scraping the thickness.px solid; BORDER-LEFT: #f0f0f0; PADDING-BOTTOM: 5px; PADDING-LEFT: 10px; PADDING-RIGHT: 10px; BACKGROUND: rgb(255,255,255); BORDER-TOP: #f0f0f0; 1px solid; PADDING-TOP: 5px" valign="center" width="138">

No exception

No exception

Qualified

Water resistance (96h)

No exception

No exception

Qualified

Bonding strength, Mpa

Standard status: ≥0.6 Freeze-thaw cycles (5 times): ≥0.4

Standard state: 1.2 Freeze-thaw cycle (5 times): 0.8

Qualified

Dynamic cracking resistance, mm

Base layer cracks≥0.1,<0.3

Base layer crack 0.3mm

Qualified

IV. Construction methods:

1. The surface of the base layer must be solid, clean, flat, free of dirt, loose and sandy , no peeling.

2. This product is a single component and can be used directly after opening the cap.

3. Apply this product 2-3 times for a full batch, the scraping thickness is about 0.5mm, and the re-coating interval is 6 hours (25℃).

4. The last layer of putty should be scraped and smoothed. If there are knife marks, gently smooth them with sandpaper before solidifying. Do not over-sand.

5. Thickness of the coating after drying It is advisable not to be less than 1.5m.

6. Construction temperature 5-40 ℃

5. Packaging and storage:

This product is packed in paper plastic bags, 50kg ± 1kg each bag. This product should be stored dry and protected from moisture.

��0.5mm, the recoating interval is 6 hours (25℃).

4. The last layer of putty should be scraped and smoothed. If there are knife marks, gently smooth them with sandpaper before solidifying. Do not over-sand.

5. Thickness of the coating after drying It is advisable not to be less than 1.5m.

6. Construction temperature 5-40 ℃

5. Packaging and storage:

This product is packed in paper plastic bags, 50kg ± 1kg each bag. This product should be stored dry and protected from moisture.

</p

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.allhdi.com/archives/18241

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Back to top
Home
E-mail
Products
Search