Toluene diisocyanate manufacturer Knowledge Chloroacetone Chloroacetone

Chloroacetone Chloroacetone

Chloroacetone structural formula

Structural formula

Business number 01NZ
Molecular formula C3H5ClO
Molecular weight 92.52
label

None yet

Numbering system

CAS number:78-95-5

MDL number:MFCD00000936

EINECS number:201-161-1

RTECS number:UC0700000

BRN number:605369

PubChem number:24846855

Physical property data

1. Properties: Colorless liquid with a strong irritating odor. Tear-jerking.

2. Density (g/mL, 25/4℃): 1.1260

3. Relative density (20℃, 4℃): 1.14819.5

4. Melting point (ºC): -44.5

5. Boiling point (ºC, normal pressure): 119.5

6. Boiling point (ºC, 5.2kPa) : 61 (ºC, 6.67kpa)

7. Refractive index: 1.4350

8. Flash point (ºC): 27 (open cup)

9. Refractive index at room temperature (n20): 1.43419.5

10. Refractive index at room temperature (n25): 1.4300

11. Vapor pressure (kPa, 25ºC): Uncertain

12. Saturated vapor pressure (kPa, 60ºC): Uncertain

13. Heat of combustion ( KJ/mol): Uncertain

14. Critical temperature (ºC): Uncertain

15. Critical pressure (KPa): Uncertain

16. Log value of oil-water (octanol/water) partition coefficient: Uncertain

17. Explosion upper limit (%, V/V): Uncertain

18. Explosion lower limit (%, V/V): Uncertain

19. Solubility: Miscible with ethanol, ether and chloroform, and soluble in 10 times the weight of water.

Toxicological data

1. Acute toxicity

Human oral LCL0: 605 ppm/10M

Rat LD50: 100mg/kg; rat inhalation LC50: 262ppm/1H

Rat abdominal cavity LD50: 80 mg/kg

Mouse abdominal cavity LD50: 127mg/kg;

Mouse abdominal cavity LD50: 92 mg/kg

Rabbit skin LD50: 141 mg/kg

Pig skin LD50: 100 uL/kg

2. Other multi-dose toxicity data

Rat caliber TCLO: 650 mg/kg/17D-I

3. Teratogenicity

Salmonella: 6mg/L

Drosophila: 100 pph/6M

Ecological data

None yet

Molecular structure data

1. Molar refractive index: 20.82

2. Molar volume (cm3/mol): 86.5

3. Isotonic specific volume (90.2K ): 195.0

4. Surface tension (dyne/cm): 25.7

5. Polarizability (10-24cm3): 8.25

Compute chemical data

1. Reference value for calculation of hydrophobic parameters (XlogP): 0.6

2. Number of hydrogen bond donors: 0

3. Hydrogen bondsNumber of receptors: 1

4. Number of rotatable chemical bonds: 1

5. Number of tautomers: 3

6. Topological molecular polarity Surface area 17.1

7. Number of heavy atoms: 5

8. Surface charge: 0

9. Complexity: 42.2

10 .The number of isotope atoms: 0

11. The number of determined atomic stereocenters: 0

12. The number of uncertain atomic stereocenters: 0

13. Determined number of stereocenters of chemical bonds: 0

14. Number of uncertain stereocenters of chemical bonds: 0

15. Number of covalent bond units: 1

Properties and stability

1. It can evaporate with water vapor, darken and become resinous under light. Add 0.1% water or 1% calcium carbonate as a stabilizer.

2.It is highly irritating to biological tissues. It decomposes under the action of sunlight to produce a highly tear-inducing gas. The gas is 0.018mg /L has a tear-inducing effect. Humans can endure less than 1 minute in an atmosphere of 0.11mg/L. During production, the equipment should be sealed and operators should wear protective gear, paying special attention to eye protection.
 

Storage method

This product should be sealed and stored in a cool, dark place. Packed in 500mL glass bottles and external wooden boxes, handle with care. Store and transport according to regulations on toxic chemicals.

Synthesis method

1. Acetone chlorination method: Stir acetone and calcium carbonate to form a slurry, heat to reflux, stop heating and add chlorine gas. After about 3-4 hours, add water to dissolve the generated calcium chloride, and the reaction solution is divided into two layers. The oil layer is collected and then refined to obtain the finished product.

2. Non-chlorine chlorination of acetone The method uses acetone as raw material and is obtained by chlorinating the chlorine gas produced by the reaction and decomposition of oxidants such as potassium chlorate and hydrogen chloride.

3. Chlorinated cyanuric acid The acid method uses trichlorocyanuric acid as the halogenating agent, sulfuric acid aqueous solution as the catalyst, and performs a chlorination reaction on acetone. This process was developed abroad in the early 1990s. Its synthesis method is simple and its product content is high.

Purpose

Used as an organic synthesis intermediate in the production of dyes, pesticides, medicines, spices, antioxidants, desiccants, vinyl photosensitive resins, color film coupling agents, etc.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.allhdi.com/archives/41951

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Back to top
Home
E-mail
Products
Search