Toluene diisocyanate manufacturer Knowledge The difference between acetonitrile and methanol used in HPLC_Kain Industrial Additive

The difference between acetonitrile and methanol used in HPLC_Kain Industrial Additive

The difference between acetonitrile and methanol used in HPLC_Kain Industrial Additive

1. First of all, the price of acetonitrile is high

The price of acetonitrile, especially HPLC grade, is very high. However, according to the conditions shown in the literature or LC manufacturers, acetonitrile is often used. Why is this? Let’s talk about this now.

2. Absorbance

Acetonitrile HPLC grade small. Among the absorption spectra of commercially available HPLC grades and premium grades of acetonitrile and methanol, acetonitrile HPLC has the smallest absorption (especially at short wavelengths). The so-called HPLC grade removes UV-absorbing impurities and limits the absorbance to within the specified value at a specified wavelength. During UV detection, the noise generated is small, so acetonitrile HPLC grade is most suitable for high-sensitivity analysis at short UV wavelengths. In addition, acetonitrile HPLC grade produces fewer ghost peaks on the gradient baseline in UV detection. Although there are various other organic solvents with high water miscibility, it is difficult to find smaller absorption than acetonitrile HPLC grade. In addition, although the spectra obtained between the HPLC grade and superior grade of methanol are not much different, the superior grade cannot guarantee the absorbance and may cause deviation, and the price is not much different, so try to use HPLC grade.

3. Pressure

Acetonitrile is low, and the pressure within the column varies depending on the type of organic solvent or the mixing ratio. In the relationship between the ratio of water/acetonitrile and water/methanol mixtures and the infusion pressure, when methanol is mixed with water, the pressure increases. , whereas acetonitrile also mixes with water and does not. Therefore, acetonitrile does not add excess pressure to the column at the same flow rate. From the above two items, we can confirm the significance of using acetonitrile. Then, besides the price, does methanol have any chemical advantages?

4. Elution ability

In general, acetonitrile is stronger. When acetonitrile and methanol are mixed with water at the same ratio, generally acetonitrile has a strong elution ability. Especially when the mixing ratio is low, in order to obtain the same retention time from the elution point of caffeine and phenol, the ratio of acetonitrile only needs to be less than half of the ratio of methanol. On the other hand, when the organic solvent is 100% or very close to this, methanol often has a strong elution ability from the perspective of carotene and cholesterol. When the mixing ratio is special, such as 50:1, the modulation error will be large, affecting the retention time, or the equilibrium time will be long. When acetonitrile encounters this situation, use a 10:1 mixture of methanol instead of acetonitrile, which is more convenient to operate. When the solvent is affected by temperature, container quantification is not used, but the weight method (considering specific gravity) can be used to reduce the error in the mixing ratio.

5. Selectivity of separation (elution)

The difference between the two is that acetonitrile and methanol have different separation selectivities. This is due to the different chemical properties of organic solvent molecules (methanol and ethanol are protic, acetonitrile and tetrahydrofuran are aprotic). Therefore, if the selectivity of separation cannot be obtained with acetonitrile, try methanol.

6. Peak shape

There is a difference in usage. For example, salicylic acid compounds (phenol compounds having a carboxyl group or a methoxy group at the ortho position) have a large tail when acetonitriles are used, but can be suppressed by methanols. However, in general, polymer-based reversed-phase columns tend to have wider peak shapes than silica gel columns. This is especially common when polystyrene columns are used to analyze aromatic compounds, etc. This is very noticeable when the mobile phase is methanol, but not when using acetonitrile. For this reason, it is recommended to use the latter (acetonitrile) when using a polymer-based reversed-phase column, because acetonitrile makes the gel swell.

7. When degassing the mobile phase, pay attention to acetonitrile

The preparation of the mixed solvent is not mentioned in the LC device, but only in the mobile phase bottle in advance (equal concentration system). Methanol generates heat when mixed with water, and excess dissolved air can easily turn into bubbles (degassing is easy). Acetonitrile cools by absorbing heat and produces bubbles as it slowly returns to room temperature, so degassing (heating and stirring, membrane filtration, He degassing, etc.) must be considered.

8. Conclusion

The above comparison of acetonitrile and methanol, commonly used mobile phases in reversed-phase chromatography. Roughly speaking, it is best to use acetonitrile HPLC grade. When selectivity and peak shape are poor, try methanol HPLC. However, it is also necessary to design analysis conditions according to various properties.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.allhdi.com/archives/10694

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Back to top
Home
E-mail
Products
Search